Skip to main content
Sell
Sell

Used 2005 Mack Dump Trucks For Sale in New York

Used 2005 Mack dump trucks for sale in New York: compare Granite axle setups, check salt corrosion, and verify engine history and legal payload.

3 Listings

Selling a used 2005 mack dump truck? List your used 2005 mack dump truck for sale and reach thousands of commercial buyers.

Used 2005 Mack Dump Trucks in New York

Salt exposure and hydraulic operating hours deserve close attention on used 2005 Mack dump trucks for sale in New York. The Granite CV generation includes CV712 single-rear-axle and CV713 tandem-drive configurations, with auxiliary lift axles on some heavier setups. Mack AI and AMI diesels with Fuller 8LL or Mack manual transmissions are familiar combinations, but verify engine and transmission identification rather than relying on the hood badge. Factory-original 2005 engines predate DPF and SCR/DEF systems; retrofits and public-contract emissions requirements still need checking.

Aggregate hauling, asphalt work and municipal snow duty put different demands on these tipper trucks. Match body capacity and material to the load, then check the tailgate, floor, hoist mounts and subframe for distortion or repairs. New York road salt makes frame flanges, crossmembers, spring hangers, air tanks and brake plumbing priority inspection points, especially after plow-and-sander service. Test the hydraulics through a complete cycle and inspect raised-body components only with the body properly supported. Compare ECM hours, odometer readings and service records for evidence of prolonged idling or component replacement.

Legal payload starts with a certified empty weight, not body volume or the sum of axle ratings. Check GVWR, tire capacity, axle spacing and load distribution against New York route limits, posted bridges and any applicable permit conditions. A lift axle does not automatically authorize more weight. Shorter wheelbases suit tight municipal sites, while heavier aggregate work may justify additional axles; spring versus air suspension also affects jobsite suitability and maintenance.

Frequently Asked Questions about Used 2005 Mack Dump Trucks in New York

Should I choose an aluminum or steel body on a 2005 Mack dump truck?

Aluminum generally favors payload-sensitive aggregate hauling, while steel is usually the better choice for demolition debris, broken concrete and severe impact loading. On a used 2005 Mack dump truck, body construction matters as much as material: inspect floor thickness, crossmember spacing, repairs and any liner. Aluminum can crack around mounts and welds, while steel floors can thin from abrasion even when fresh paint makes the exterior look sound.

Is a Fuller 8LL a good transmission for a 2005 Mack dump truck?

A Fuller 8LL is well suited to slow jobsite maneuvering because its deep-reduction gearing provides very low working ratios. A Mack T310 can also suit dump service, but compare actual low and reverse ratios rather than counting speeds. On a 2005 Mack dump truck, test clutch engagement, shifting and PTO operation, and check for driveline vibration. Rear-axle ratio and tire size also determine how effectively the truck starts and crawls under load.

Does a 2005 Mack dump truck need a diesel emissions inspection in New York?

A New York-registered 2005 Mack dump truck over 8,500 pounds GVWR generally needs an annual diesel emissions inspection if registered in the New York Metropolitan Area. That requirement is separate from the annual safety inspection. Heavy-duty diesels operating elsewhere in the state can face roadside emissions checks. Confirm applicable exemptions with New York DMV, and verify public-agency contract requirements separately because passing an inspection does not establish eligibility for every government job.

What paperwork should prove an engine rebuild on a 2005 Mack dump truck?

Itemized invoices tied to the installed engine’s serial number provide stronger evidence than an undocumented overhaul claim on a 2005 Mack dump truck. Ask which internal components were replaced, what machining was performed, and whether injectors, turbocharger and cylinder-head work were included. Record rebuild mileage and hours alongside current readings. An engine rebuild does not automatically renew the clutch, transmission, rear axles or cooling system, so those components need separate maintenance records and inspection.